Highly powerful water-repellent for porous materials
ImperGuard® Ultra 4 in 1 is highly powerful water-repellent resistant to water, fungi, grease, stains and with mineralisation effect reinforcing the stone against ingress.
Action 1: Water-repellent, protects porous materials from rainwater penetration and also suppresses the harmful effects of ingress, acid rain, erosion, freeze/thaw cycle.
Action 2: Anti-green deposits, it limits the formation of mosses, lichens and fungi.
Action 3: Anti-stain, sustainably inhibit the penetration of all types of soiling, even greases. Easy to maintain the substrate.
Action 4: Remineralisation effect, reinforcing the masonry against ingress.
ImperGuard® Ultra 4 in 1 is a non-film forming impregnation product, the material remains permeable to air and water vapour. Completely clear after application, it does not change the nature of the treated material (no risk of bleaching). It is also fully resistant to UV rays and does not yellow over time.
Used outside on porous floors, façades and roofs. Ideal for all types of material: natural or reconstituted stone, concrete, plaster, brick, terracotta, slate, cement, autoblocking paving stones etc.
  • Highly powerful water-proofing, resistant to water, fungi, grease, stains and with reimineralisation effect reinforcing the stone against ingress.
  • Protects porous materials from rainwater penetration and also suppresses the harmful effects of ingress, acid rain, erosion, freeze/thaw cycle, formation of mosses, green deposits and lichens, efflorescence etc.
  • Anti-stain properties that sustainably inhibit the penetration of all types of soiling, even greases. Easy to maintain the substrate.
  • Remineralisation effect reinforcing the masonry against ingress.
  • Next generation impregnation product that does not product films. It is colourless after application, it does not change the appearance of the treated substrate. Very good U.V.-resistance, it does not turn yellow.
Apply with a low-power spray, roller or brush.
  
Clean tools and equipment used with water immediately after use.
Apply the product to a clean, dust-free, degreased and dry surface. To remove any black stains, pollution or soiling that invades the materials, use Guard® Wash Express. To remove traces of efflorescence, laitance or cement residues, use neat Guard Remover® Eco Efflorescence & Cement.
  • Use the product neat, do not dilute.
  • Shake the packaging well before use and carry out a preliminary test.
  • The substrate must be impregnated up to saturation in two to four “wet-on-wet” layers.
  • Do not overload the substrate, remove any excess after drying.
  • For vertical surfaces, apply from bottom to top.
  • Drying protected: 24 hours.
  • Maximum effect reached after 7 days.
  • Physical state at 20°C: Liquid.
  • Colour: Milky.
  • Odour: Slight.
  • pH: 8 ± 0.5.
  • Boiling point [°C]: 100 °C.
  • Density: 1.0 ± 0.02.
  • Water solubility [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
Consumption depends on the porosity of the material. The following figures are given for information: 6 to 8 m²/litre.
5 and 20 litres.
  • Store in a dry place at a temperature between 5°C and 30°C.
  • Storage: 12 months from date of manufacture, in original packaging unopened.
5 years.
Domestic stains may be washed with clean water or using a pH neutral cleaner.
Respects the environment and is ecological:
  • Without petroleum solvents.
  • Non-hazardous.
  • Biodegradable by more than 90%**.
  • VOC < 2 g/l*.
  • Only treat surfaces previously cleaned of all atmospheric pollution and stains.
  • Do not dilute or mix with another product.
  • Do not apply to organic, metal or impermeable materials. Frames and windows must be protected. Accidental colouring and stains must be cleaned immediately with water.
  • The product may slightly accentuate the colour (satin effect). Always do a test on the substrate to be treated before applying.
  • In case of contact with glass materials, immediately rinse with water.
  • For a perfect application and effective protection, the product must stirred and used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply in rainy or very hot weather. Air temperature between 5°C and 30°C.
  • Respiratory protection: No breathing apparatus is required under normal conditions of use provided there is adequate ventilation.
  • Protection of hands: Wear chemical-resistant gloves.
  • Skin protection: No special clothing or skin protection is recommended under normal conditions of use.
  • Protection of eyes: If there is a risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature
Aqueous emulsion based on resins of silane, siloxane, fluorine and acrylic.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com

NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
www.nanophamgroup.com
www.congnghenano.vn
www.bacsivatlieu.vn
www.guardindustrie.com.vn

Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 62
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.157.717