Specialist
Solution
Product
Document
Picture
Permanent protection against graffitifor concretes
AntiGraffitiGuard®Special Concreteis a two-part anti-graffiti product. It durably protects concretes against all kinds of graffiti and tags (paint, felt pens, etc.) and dirt.
AntiGraffitiGuard®Special Concrete protects treated surfaces permanently. It can be cleaned dozens of times (using GraffiGuard®2010 graffiti cleaner) and will still keep working, so does not need to be reapplied after graffiti has been removed.
AntiGraffitiGuard®Special Concrete is available in flat and gloss versions.
AntiGraffitiGuard®Special Concrete is used indoors as well as out on all kind of vertical concretes: regular concrete, reinforced concrete, fiber concrete, UHPC, etc.
  • Permanent protection from graffiti.
  • Protects from hydrocarbons, grease, organic pro-ducts.
  • Protects from water-borne chemical or biological agents.
  • Gives the substrate a satin look.
  • Good resistance to the mechanical actions of rub-bing and scratching.
  • Excellent durability under UV action.
  • Safe and non-toxic.
For better control and ideal results, it is recom-mended that AntiGraffitiGuard®Special Concrete be applied using an HVLP type spray gun. Application with a roller or a brush is also possible.
Clean tools and equipment after use with water.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove stains and marks of pollution use Guard Cleaner®Polluted Facades, for greasy stains use Guard Cleaner®EcoSoiledFloorsand for efflorescence, chalking or concrete bloom use Guard Remover®EcoEfflorescence & Cement.
  • The conditions of application and substrate prepara-tion must meet French unified code of practice DTU 59.1.
On regular concretes:
  • Begin by applying PrimerGuard®with a brush, roller or an HVLP sprayer to promote adhesion (coverage: 8 to 12 m2 per litre). Wait a minimum of 4 hours (maximum of 48 hours) before applying AntiGraf-fitiGuard®Special Concrete. For more information refer to the Primer Guard® data sheet.
On UHPC:
  • Begin by applying PrimerGuard® Special UHPC with a brush, roller or an HVLP sprayer to promote adhesion (coverage: 12 to 15 m2 per litre). Wait a minimum of 4 hours (maximum of 48 hours) before applying AntiGraffitiGuard®Special Concrete. For more information refer to the PrimerGuard® Special UHPC data sheet.
  • Surface preparation before application has a major influence on the final appearance and performance of the coating, especially as regards the adhesion of AntiGraffitiGuard®Special Concrete to the subs-trate.
  • Always carry out a test first.
  • AntiGraffitiGuard®Special Concrete is prepackaged in the correct ratios. All of component A must the-refore be mixed with all of component B. Under no circumstances modify the A:B ratio.
  • Before use, thoroughly mix part A (base) using an electric stirrer until a homogeneous liquid is obtai-ned.
  • Stirring continuously, add part B (hardener) to part A (base). Blend at moderate speed with an electric mixer for at least 5 min. Leave for half an hour to allow bubbles to escape, then homogenise again with the electric mixer before application.
  • Once prepared, the mixture can be used for 4 hours at an ambient temperature of less than 20°C.
  • Physical state at 20°C: Liquid.
  • Appearence: Whitish.
  • Odour: Odourless.
  • pH: 7.5 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.06 ± 0.02.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline: 120 to 200 g/m2 for two layers.
Kits of 1 and 5 litres (basis and hardener to be mixed).
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
  • Stubborn dirt should be cleaned off with clean water or with Guard Cleaner®Eco Soiled Floors diluted with 50% water.
  • Graffiti can be cleaned using GraffiGuard®2010.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • Biodegradable > 80%*.
  • VOC < 30 g/l*.
  • Only treat surfaces that have first been cleaned of all atmospheric pollution and all stains.
  • For ideal application and effective protection, AntiGraffitiGuard®Special Concrete must be stirred, and it is critical that it be used when the temperature of the substrates is between 10°C and 30°C.
  • Do not apply during rain, or in very hot weather or in strong winds. Temperature between 10°C and 30°C.
  • Normal protective gear must be used when the product is applied by spray gun.
  • Do not dilute (except for the 1st layer if necessary) or mix with any other product.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no spe-cial respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: Wear protective clothing with long sleeves.
  • Eye protection: Wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature:
Two-part aqueous-phase polyurethane.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: +84 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 67
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.873
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other