Specialist
Solution
Product
Document
Picture
Protective multi-substrate colourless non-slip wax
Polish’Guard® is an acrylic emulsion containing metal ions that create a tough wear layer. Polish’Guard® is particularly designed for treating a wide variety of substrates, as well as substrates protected by the ProtectGuard® range of protective products. When diluted to 1 volume of product to 9 volumes of water, Polish’Guard® can also be used for regular maintenance.
Polish’Guard® is used indoors for treating horizontal porous inorganic surfaces (concrete, terracotta, brick, cement, cement tiles), plastic surfaces, linoleum, wood etc. Polish’Guard® is used for new and renovated constructions.
  • Forms a non-slip wear layer that keeps the protected substrate cleaner for longer.
  • Easy to clean.
  • Good abrasion- and scratch-resistance.
  • Imparts a gloss look.
  • Use neat for the 1st application, diluted for maintenance.
  • Easy to use.
Apply using a terry towel type cloth or an applicator.

Clean tools and equipment immediately after use with water.
Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove grease stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • 1st application: Use product neat – do not dilute.
  • For optimum results, apply 2 or 3 thin coats of Polish’Guard® without overcharging the substrate.
  • Wait approx. 30 min for drying between the 2 coats.
  • Apply 2nd coat at right angles to the 1st.
  • To bring out the gloss, a 3rd coat may be applied after 30 minutes’ dryingtime.
  • For extra gloss and toughness, buff Polish’Guard® with a a high-speed brushing machine (400 t/min) with a white disk.
  • Drying time before permitting traffic again: 6 hours.
  • Physical state at 20°C: Liquid.
  • Appearence: Milky.
  • Odour: Slight.
  • pH: 8 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.01 ± 0.01.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
The figures below should be used only as a general guideline:
  • Raw concrete: 6 to 10 m²/litre.
  • Protected concrete: 15 to 20 m²/litre.
  • Plastic surface: 20 to 25 m²/litre.
  • Maintenance: 20 to 40 m²/litre.
5 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 24 months following the production date when kept in the original unopened container.
  • Regular maintenance of floors can be done using Polish’Guard® diluted to 1 volume to 9 volumes of water to regenerate the gloss.
  • Stubborn dirt should be cleaned off with clean water or with Guard Cleaner® Eco Soiled Floors diluted with 50% water.
  • Polish’Guard® can be stripped off completely with Guard® Remover Eco Floor Wax.
Environment-friendly product: 
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Safe and non toxic.
  • Biodegradable > 80%*.
  • VOC = 36 g/l*.
  • Rating for VOC emissions into idoor air: A+.
  • Do not treat surfaces until they have first been cleaned of all atmospheric pollution and all stains.
  • For effective protection, Polish’Guard® must be stirred and it is essential that it be used only when the substrate temperature is between 10°C and 30°C.
  • Do not apply in rain or very hot weather. Air temperature between 5°C and 30°C.
  • Do not mix with another product.
  • Do not apply to enamelled surfaces, polished or crystalline surfaces, extruded clay tiles or earthenware and surfaces treated with ProtectGuard® WF.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature
Acrylic binder containing metal ions in an aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: +84 918 244 844
Email: global@nanophamgroup.com
Website: 
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 70
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.881
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other