Specialist
Solution
Product
Document
Picture
Clear primer for adhesion of super antigraffiti guard
Primer Guard® S200 is a product designed to be used as a primer before applying Super AntiGraffiti Guard®.
Primer Guard® S200 is used on:
  • Non-porous construction materials.
  • Primer Guard® S100. 
It promotes the adhesion of Super AntiGraffiti Guard® on the material and thus avoids premature detachment of the protection.
Primer Guard® S200 is used indoors and outdoors on vertical surfaces. It is intended to be applied before the Super AntiGraffiti Guard® on non porous substrates or treated with Primer Guard® S100.
Its yellow / brown tracer makes it possible to ensure the homogeneity of the application. This color disappears spontaneously even if the support is covered by the Super AntiGraffiti Guard®.
  • Greatly facilitates adhesion of Super AntiGraffiti Guard®.
  • Ready to use.
  • Easy to use.
  • Tracer effect to facilitate its uniform application.
Apply using an HVLP type gun, a brush or a roller.

Clean used tools and equipment with soapy water immediately after use. After drying, use acetone or substitute acetone.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove stains and marks of pollution use Guard Cleaner® Eco Soiled Floors.
  • Metal surfaces should be cleaned with a cloth soaked in acetone or acetone substitute. Leave to dry before applying the primer.
  • Shake the product well for 1 minute before use.
  • Always carry out a preliminary test.
  • Apply one coat from the bottom up.
  • It is essential that PrimerGuard® S200 be completely dry to the touch before applying of Super AntiGraffiti Guard®.
  • PrimerGuard® S200 must be protected from dust for the first 15 min following application.
  • PrimerGuard® S200 is recoverable in 30 min at a temperature of 20°C. Depending on the weather conditions, the delay can be up to 1 hour.
  • Physical state at 20°C: Liquid
  • Appearence: Yellow brown
  • Odour: Caracteristic
  • pH: Non applicable
  • Boiling point [°C]: 56°C
  • Density: 0.82 ± 0.05
  • Solubility in water [vol/vol]: Miscible
  • Point d’éclair [°C]: -18°C
  • VOC*: < 750g/l
Coverage depends on the porosity of the material.
When applying to HVLP, consider losses due to spraying the product (approximately 20%). 
The figures below should be used only as a general guideline:
  • Mineral surfaces with very low porosity: 15 to 20 m²/litre.
  • Metal or plastic surfaces: 20 to 25 m²/litre.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 6 months following the production date when kept in the original unopened container.
  • The product tends to take the form of two phases (a phenomenon known as syneresis) during storage. It is therefore essential to shake the can for 1 minute before use.
  • Do not treat surfaces until they have first been cleaned of all atmospheric pollution and all stains.
  • For ideal application and effective protection, it is essential that PrimerGuard® S200 be used when the substrate temperature is between 10°C and 30°C.
  • Do not apply in rain or very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with another product.
  • Respiratory protection: Wear full face respirator complying with recognized standards, such as NF EN 136. Recommended Filter Type: ABEKP2 combination filter (certain inorganic, organic and acidic gases, vapors, ammonia / amines, particulates), in accordance with recognized standards as NF EN 14387.
  • Hand protection: Wear butyl rubber gloves (refer to MSDS for more information).
  • Skin protection: Wear protective clothing or skin protection.
  • Eye protection: Wear protective & waterproof goggles. (See MSDS for more information).
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
PROFESSIONAL PRODUCT
Chemical nature
Mix of silicone resin and silane in the solvent phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 71
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.883
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other