Specialist
Solution
Product
Document
Picture
Clear primer for minimizing the wet effect induced 
By super antigraffiti guard
  • Primer Guard® S100 is a product designed to be used as a primer before applying Super AntiGraffiti Guard®. Primer Guard® S100 is used on porous materials.
  • It reduces the impregnation of Super AntiGraffiti Guard® in the material and thus avoids the hue enhancing effect of the protection.
Primer Guard® S100 is used indoors and outdoors on vertical surfaces. It is intended to be applied before the Primer Guard® S200 (primer to ensure the adhe-sion of the Super AntiGraffiti Guard®).
  • Greatly reduces the wet effect of Super AntiGraffiti Guard®.
  • Ready to use.
  • Easy to use.
  • Nonflammable.
Apply using an HVLP type gun, a brush or a roller.
Clean tools and equipment immediately after use with water.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove stains and marks of pollution use Guard Cleaner® Polluted Facades on stone and Guard Cleaner® Eco Soiled Floors on concrete. For efflores-cence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement. 
  • Use the product neat: do not dilute.
  • Shake the product well for 1 minute before use and always carry out a preliminary test.
  • Apply one coat from the bottom up.
  • It is essential that PrimerGuard® S100 be completely dry to the touch before applying PrimerGuard® S200.
  • PrimerGuard® PrimerGuard® S100 must be protected from dust for the first 30 min following application.
  • PrimerGuard® S100 is recoverable in 1 hour at a temperature of 20°C. Depending on the weather conditions, the delay can be up to 24 hours.
  • Physical state at 20°C: Liquid
  • Appearence: Whitish 
  • Odour: Odourless
  • pH: 7 ± 0.5
  • Boiling point [°C]: 100°C
  • Density: 1.01 ± 0.05
  • Solubility in water [vol/vol]: Partially soluble
  • Flash point [°C]: Not applicable
Coverage depends on the porosity of the material. When applying to HVLP, consider losses due to spraying the product (approximately 20%).
The figures below should be used only as a general guideline: 10 to 12 m2/litre.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 6 months following the production date when kept in the original unopened container.
Environment-friendly product: 
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Safe and non toxic.
  • VOC < 5 g/l*.
  • The product tends to take the form of two phases (a phenomenon known as synere-sis) during storage. It is therefore essential to shake the can for 1 minute before use.
  • Do not treat surfaces until they have first been cleaned of all atmospheric pollution and all stains.
  • For ideal application and effective protection, it is essential that PrimerGuard® S100 be used when the substrate temperature is between 10°C and 30°C.
  • Do not apply in rain or very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with another product.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
PROFESSIONAL PRODUCT
Chemical nature
Dispersion of styrene / acrylic copolymer in aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 70
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.937
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other