Specialist
Solution
Product
Document
Picture

Water & oil repellent, self-cleaning and pollution-removing total protection of porous building materials.

ProtectGuard® Dtox is an innovative product which combine water-repellent, oil-repellent, anti-graffiti and pollution-removing properties.
ProtectGuard® Dtox offers long-lasting protection against water, atmospheric pollution, grease-type staining, penetration of liquids and graffiti.
A material treated with ProtectGuard® Dtox becomes virtually self-cleaning and will be easier to maintain.
ProtectGuard® Dtox uses photocatalytic action to remove pollutants present in outdoor air and breaks down organic pollution.
Air is therefore purified.
ProtectGuard® Dtox is a non film-forming impregnation product that leaves the treated surface permeable to air and water vapour.
ProtectGuard® Dtox is completely colourless after application and does not change the appearance or the composition of the treated surface. It is also UV-resistant and does not discolor with age. ProtectGuard® Dtox is available in a coloured version (ProtectGuard® Color Dtox).
Substrate preparation:
  • Apply the product to a surface that is clean, dust-free, greasefree and dry. To remove stains and marks of pollution use Guard Cleaner® Polluted facades. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
Application:
  • Use product neat - do not dilute.
  • Shake container well before use. Test first.
  • The treated surface should be impregnated to saturation point, either in one application or in two applications ‘wet-on-wet’.
  • Do not over apply, eliminate exceeding product before drying.
  • Drying time: 24 hours.
  • Optimum effectiveness obtained after 7 days.
  • Protects against water and grease.
  • Anti-staining, anti-dirt and anti-adhesion.
  • Photocatalytic removal of pollution: purifies outside air.
  • Makes surfaces self-cleaning.
  • Limits formation of efflorescences.
  • Limits development of moss and lichens.
  • Makes materials more resistant to atmospheric pollution.
  • Makes cleaning easier.
  • Good anti-graffiti properties.
  • Prevents degradations due to ‘freezethaw’ cycles.
  • Non film-forming, lets a surface breathe.
  • UV-resistant, does not yellow.
  • Ready and easy to use.
Apply using a low pressure sprayer, a roller or a brush.
* Calculation based on the components’ data.
Clean tools and equipment immediately after use with water.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline

 

  • Physical state at 20 °C: Liquid
  • Colour: Uncoloured
  • Odour: None
  • pH: 6.5 ± 0.5
  • Boiling point [°C]: 100 °C
  • Density: 1.0 ± 0.01
  • Solubility in water [vol/vol]: Total
  • Flashpoint [°C]: Not applicable
5 and 25 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
Stubborn dirt should be cleaned off with clean water or with Guard Cleaner® Eco Soiled Floors diluted with 50% water.
Environmentally friendly and ecological:
  • Water-based product.
  • Petroleum solvent-free.
  • Silicone-free.
  • Safe and non-toxic.
  • VOCs < 2 g/l*.
  • 100% biodegradable*.
  • Remove all atmospheric pollution-related dirt from all surfaces to be treated before starting the treatment.
  • For best results it is essential that ProtectGuard® Dtox is used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply during rain or in very hot weather.
  • Air temperature between 5°C and 30°C. Do not dilute or mix with any other product.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
  • KEEP OUT OF THE REACH OF CHILDREN
Chemical nature
Acrylic copolymer in aqueous phase and photoactive titanium dioxide.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 69
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.927
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other